CCNP questions

CCNP questions ORDER NOW FOR CUSTOMIZED AND ORIGINAL ESSAY PAPERS ON CCNP questions Question 8 0 / 1 point You administer the routers shown in the diagram below. You issue the following commands on RouterA: ? RouterA(config)#router bgp 100 ? RouterA(config-router)#neighbor 192.168.2.1 remote-as 100 ? RouterA(config-router)#neighbor 10.1.2.1 remote-as 200 You issue the following commands on RouterB: ? RouterB(config)#router bgp 100 ? RouterB(config-router)#neighbor 192.168.1.1 remote-as 100 ? RouterB(config-router)#neighbor 192.168.1.1 route-reflector-client ? RouterB(config-router)#neighbor 192.168.3.1 remote-as 100 ? RouterB(config-router)#neighbor 192.168.3.1 route-reflector-client You issue the following commands on RouterC: ? RouterC(config)#router bgp 100 ? RouterC(config-router)#neighbor 192.168.2.1 remote-as 100 ? RouterC(config-router)#neighbor 10.1.3.1 remote-as 300 Which of the following statements is accurate regarding the network? (Select the best answer.) Question options: ? You must issue the neighbor 192.168.2.1 route-reflector-client command on RouterA and RouterC. ? You can disable synchronization on the routers in AS 100. ? RouterA can communicate with RouterD by using IBGP. ? RouterA and RouterC must be directly connected for traffic to pass between AS 200 and AS 300. Question 19 0 / 1 point You administer the network shown in the diagram. You want to configure a 6to4 tunnel between Router A and Router B. You issue the sh running-config command to check the configuration (output in the diagram). Which of the following sets should you issue on Router A? Question options: A) RouterA(config)#interface tunnel 0 RouterA(config-if)#ip address 192.168.1.1 RouterA(config-if)#tunnel source 2002:C0A8:0101::1/64 RouterA(config-if)#tunnel mode 6to4 B) RouterA(config)#interface tunnel 0 RouterA(config-if)#ip address 192.168.1.1 RouterA(config-if)# tunnel source 2002:C0A8:0101::1/64 RouterA(config-if)#tunnel source FastEthernet 0/0 RouterA(config-if)#tunnel mode ipv6ip 6to4 RouterA(config-if)#exit RouterA(config)#ip route 2002::/16 tunnel 0 C) RouterA(config)#interface tunnel 0 RouterA(config-if)#ip address 192.168.1.1 RouterA(config-if)#tunnel source FastEthernet 0/0 RouterA(config-if)#tunnel mode ipv6ip 6to4 Question 21 0 / 1 point You configure RouterA to redistribute OSPF Type 1 external routes with a metric of 5 and all OSPF routes with a tag of 7. Which of the following lines of output will be displayed when you issue the show running-config command? (Select the best answer.) Question options: B) Route-map map1 permit 10 Match metric 5 Match tag 7 Match route-type external type-1 C) Route-map map1 permit 10 Match route-type external type-1 ! Route-map map1 permit 30 Match tag 7 D) Route-map map1 permit 10 Match metric 5 Match route-type external type-1 ! Route-map map1 permit 20 Match tag 7 Question 22 0 / 1 point You want to create a virtual link between Area 0 and Area 11. Which configuration commands would you use? (Select 2) Question options: A) Router1(config-router)#area 11 virtual-link 10.5.1.1 B) Router4(config-router)#area 7 virtual-link 10.2.1.1 C) Router5(config-router)#area 0 virtual-link 10.1.1.1 D) Router2(config-router)#area 0 virtual-link 10.3.1.1 E) Router4(config-router)#area 11 virtual-link 10.3.1.1 F) Router2(config-router)#area 7 virtual-link 10.4.1.1 Question 23 0 / 1 point You issue the show ipv6 ospf command on RouterA and receive the following output: CCNP questions RouterA#show ipv6 ospf Routing Process “ospfv3 22” with ID 10.20.30.40 SPF schedule delay 5 secs, Hold time between two SPFs 10 secs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs LSA group pacing timer 240 secs Interface flood pacing timer 33 msecs Retransmission pacing timer 66 msecs Number of external LSA 0. Checksum Sum 0x000000 Number of areas in this device is 1. 1 normal 0 stub 0 nssa Area 2 CCNP questions Number of interfaces in this area is 1 Area has no authentication SPF algorithm last executed 00:00:20.532 ago SPF algorithm executed 7 times Number of LSA 0. Checksum 0x000000 Number of DCbitless LSA 0 Number of indication LSA 0 Number of DoNotAge LSA 0 Flood list length 0 Which of the following statements are correct? (Select 3 choices.) Question options: A) RouterA is an internal router. B) RouterA is part of a stub area. C) RouterA is an ABR. D) RouterA is part of a standard area. E) Router A is part of a totally stubby area. F) RouterA is a backbone router. G) Route recalculation has occurred seven times. H) RouterA is an ASBR. Question 26 0 / 1 point RouterA connects an IPv6-only network to an IPv4-only network. You want to ensure that all devices on each network can communicate with each other. Which of the following mechanisms should you implement on RouterA to achieve your goal? (Select the best answer.) CCNP questions Question options: A) NAT-PT B) overlay tunneling C) dynamic NAT D) static NAT E) 6to4 tunneling Question 28 0 / 1 point Which of the following commands would you issue if you want to configure OSPF to consider both the internal cost and the external cost when redistributing EIGRP routes into OSPF? CCNP questions (Select the best answer.) Question options: A) redistribute eigrp 1 metric-type 1 subnets B) redistribute ospf 1 metric-type 2 subnets C) redistribute eigrp 1 metric-type 2 subnets D) redistribute ospf 1 metric-type 1 subnets Question 30 0 / 1 point Which of the following routes from the show ip route command was obtained from a Type 3 or Type 4 LSA? (Select the best answer.) Question options: IA 172.17.3.0/24 [110/74] via 10.1.2.3, 00:00:23, FastEthernet1/0 172.17.2.0/24 [110/74] via 10.1.2.3, 00:00:23, FastEthernet1/0 S 172.17.5.0/24 is directly connected, FastEthernet0/1 C 172.17.4.0/24 is directly connected, FastEthernet1/1 Question 31 0 / 1 point Which of the following two statements regarding the Cisco proprietary BGP weight feature are TRUE? Question options: A) The lower value for weight is preferred B) The higher value for weight is preferred C) Weight is only used between iBGP neighbors D) Weight is used only locally inside the router E) When set, the weight value is only communicated to eBGP peers F) When set, the weight value is only communicated to iBGP peers Question 41 0 / 1 point Based solely on the information present in the image below, which ONE (1) statement is TRUE? Question options: The command crypto key generate rsa general-keys modulus 768 label SSH-MPLS-KEYS was run to create this configuration The command crypto key generate rsa general-keys modulus 4096 label SSH-MPLS-KEYS was run to create this configuration The command crypto key generate rsa general-keys modulus 512 label SSH-MPLS-KEYS was run to create this configuration This is the default SSH configuration on Cisco routers None of the above Question 42 0 / 1 point Which ONE (1) statement below is TRUE about uRPF? Question options: uRPF can operate in either strict mode or loose mode uRPF can operate in either relaxed mode or loose mode uRPF can operate in either security mode or allow mode uRPF is defined in RFC 2728 u Question 43 0 / 1 point CCNP questions Based solely on the information present in the image below, which ONE (1) statement about uRPF is TRUE? Question options: uRPF will function in Unicast in VRF mode on interface gi0/1 uRPF will function in strict mode on interface gi0/1 uRPF will not function on gi0/1 because it does not work with RFC 1918 addresses uRPF will function in loose mode on interface gi0/1 uRPF is defined in RFC 2328 Question 46 0 / 1 point Based solely on the output in the image below, which ONE (1) statement is TRUE about the archive configuration? Question options: This configuration will result in the automatic backup of the configuration every hour This configuration will result in the automatic backup of the configuration every 13 hours This configuration will result in the router configuration being backed up each time the router is reloaded This configuration will create the backup copy of the current configuration when the command copy running-configuration startup-configuration is run This configuration will not work because you cannot save configuration backups to the flash: directory Question 47 0 / 1 point Based solely on the information present in the image below, which ONE (1) statement is TRUE about this archive configuration? Question options: This archive configuration will save backup copies of the router configuration to the flash: directory This archive configuration will keep a maximum of 90 backups This archive configuration will save the configuration automatically each time the router is rebooted This archive configuration will automatically back up the current configuration every hour This archive configuration will backup the current configuration every 90 hours Question 50 0 / 1 point You are the junior network administrator for Evil Corp. Unlimited and the senior network administrator has come to you in a panic. He is trying to enable OSPF routing protocol authentication between two (2) routers using SHA authentication, but is unable to get it to work. He shows you the output below and wants to know what you think the issue might be. What do you tell him? CCNP questions Question options: SHA authentication with OSPF is not supported on Cisco routers SHA authentication with OSPF is not supported in Cisco IOS, but it is in IOS-XE SHA authentication with OSPF is not supported in Cisco IOS, but it is in IOS-XR SHA authentication with OSPF is not supported in Cisco IOS release 12.4 SHA authentication is not supported in Cisco IOS, but it is in IOS-XE+ CCNP questions Get a 10 % discount on an order above $ 100 Use the following coupon code : NURSING10

Read more
Enjoy affordable prices and lifetime discounts
Use a coupon FIRST15 and enjoy expert help with any task at the most affordable price.
Order Now Order in Chat

We now help with PROCTORED EXAM. Chat with a support agent for more details